Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to:
Diagnostic Methods
(100-00 General Information, Description and Operation).
Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.
REFER to:
Diagnostic Methods
(100-00 General Information, Description and Operation).
Symptom Chart: Parking, Rear, and License Plate Lamps
Symptom Chart
Condition
Possible Sources
Actions
A module does not respond to the diagnostic scan tool
Fuse
Wiring, terminals or connectors
Module
REFER to:
Communications Network
(418-00 Module Communications Network, Diagnosis and Testing).
One or more parking, rear or license plate lamps is inoperative
A5
CHECK THE PARKING LAMP GROUND CIRCUIT FOR AN OPEN
For a front parking lamp, measure:
LH
Front Park Lamp
Positive Lead
Measurement / Action
Negative Lead
C1021-6
C1021-7
RH
Front Park Lamp
Positive Lead
Measurement / Action
Negative Lead
C1041-6
C1041-7
For a rear lamp, measure:
4-Door
LH
Reversing Lamp
Positive Lead
Measurement / Action
Negative Lead
C498-1
C498-4
4-Door
RH
Reversing Lamp
Positive Lead
Measurement / Action
Negative Lead
C499-1
C499-4
4-Door
LH
Rear Lamp
Positive Lead
Measurement / Action
Negative Lead
C412-2
C412-4
4-Door
RH
Rear Lamp
Positive Lead
Measurement / Action
Negative Lead
C415-2
C415-4
5-Door
LH
Rear Lamp
Positive Lead
Measurement / Action
Negative Lead
C414-4
C414-6
5-Door
RH
Rear Lamp
Positive Lead
Measurement / Action
Negative Lead
C417-4
C417-6
For a license plate lamp, measure:
Positive Lead
Measurement / Action
Negative Lead
C4216-1
C4216-2
Is the voltage greater than 11 volts?
Yes
For a front lamp, CHECK the internal headlamp harness for open or shorted circuits and damaged or pushed-out pins. If the
harness is not OK, REPAIR the harness. If the harness cannot be repaired, INSTALL a new headlamp assembly.
REFER to:
Headlamp Assembly
(417-01 Exterior Lighting, Removal and Installation).
If the harness is OK, INSTALL a new bulb.
For a rear or license plate lamp, INSTALL a new bulb.
No
REPAIR the circuit.
A6
CHECK THE PARKING LAMP SUPPLY CIRCUIT FOR A SHORT TO GROUND
Place the headlamp switch in the off position.
Disconnect:
BCM
C2280D (Front Parking Lamps).
Disconnect:
BCM
C2280G (Rear Parking or License Plate Lamps).
A8
CHECK FOR CORRECT BCM (BODY CONTROL MODULE)
OPERATION
Disconnect and inspect all
BCM
connectors.
Repair:
corrosion (install new connector or terminals – clean module pins)
damaged or bent pins – install new terminals/pins
pushed-out pins – install new pins as necessary
Reconnect the
BCM
connectors. Make sure they seat and latch correctly.
Operate the system and determine if the concern is still present.
Is the concern still present?
Yes
CHECK
OASIS
for any applicable Technical Service Bulletins (TSBs). If a
TSB
exists for this concern, DISCONTINUE this test and FOLLOW
TSB
instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new
BCM
.
REFER to:
Body Control Module (BCM)
(419-10 Multifunction Electronic Modules, Removal and Installation).
No
The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause
of any connector or pin issues. CLEAR the Diagnostic Trouble Codes (DTCs).
The Parking, Rear, Or License Plate Lamps Are On Continuously
Refer to Wiring Diagrams Cell 92 for schematic and connector information.
B2
CHECK FOR CORRECT BCM (BODY CONTROL MODULE)
OPERATION
Disconnect and inspect all
BCM
connectors.
Repair:
corrosion (install new connector or terminals – clean module pins)
damaged or bent pins – install new terminals/pins
pushed-out pins – install new pins as necessary
Reconnect the
BCM
connectors. Make sure they seat and latch correctly.
Operate the system and determine if the concern is still present.
Is the concern still present?
Yes
CHECK
OASIS
for any applicable Technical Service Bulletins (TSBs). If a
TSB
exists for this concern, DISCONTINUE this test and FOLLOW
TSB
instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new
BCM
.
REFER to:
Body Control Module (BCM)
(419-10 Multifunction Electronic Modules, Removal and Installation).
No
The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause
of any connector or pin issues. CLEAR the Diagnostic Trouble Codes (DTCs).